The maximum value corresponds to the nominal dimension, while the field amplitude of tolerance is listed in the table. Nf en the british standard bs 5950 structural need to make changes to a pdf document use of steelwork in building, including those manufactured to british. Tolerances to en 10029 for hot rolled plate 3mm and above. Products with a specified minimum yield strength 460 nmmand pdf file. This european standard shall be given the status of a national standard, either by publication of an identical. Standard continuously hotrolled strip and platesheet. This european standard shall be given the status of a national standard, either by publication of an. Tolerances on dimensions and shape is classified in these ics categories.
Ta evropski standard velja tudi za vroce valjane trakove za hladno. It is intended to publish an article on this standard on the website in the near future. En 10029, hot rolled steel plates 3 mm thick or above tolerances on dimensions, shape and mass. Standard continuously hotrolled strip and platesheet cut. En 10034, structural steel i and h sections tolerances on shape and dimensions. Inspection document on the customers request, either a test report 2. En 10020, definition and classification of grades of steel. The inspection document states the chemical composition of steel in compliance with cast analysis and the hardness of hardened plates and sheets. The standard, 1100 sw sixth avenue, portland, or 97204 standard. This standard covers continuously rolled hot rolled flat products with a rolled width of 600 2200mm inclusive in nonalloy, alloy and stainless steels. All bsi british standards available online in electronic and print formats. Uni en 10051 continuously hotrolled strip and platesheet cut from wide strip of nonalloy and alloy steels tolerances on dimensions and shape 6 tolerances for sheetplate 6. Tolerances on dimen sions and shape in en 10051, the thickness tolerances are divided according to four different yield strength classes. This european standard specifies tolerances on dimensions and shape for continuously hotrolled uncoated platesheet and strip with a maximum width of 2 200 mm of nonalloy and alloy steels in accordance with table 1.
Standard continuously hotrolled uncoated plate, sheet. Hot rolled low carbon steel sheetplate and strip for cold forming class 2. This european standard does not apply to stainless steels and not to hotrolled strip rolled in widths w en 10048. Continuously hotrolled uncoated plate, sheet and strip of. Products with a specified minimum yield strength 460 nmmand com. This european standard has been prepared by technical committee ecisstc 9, technical delivery conditions and quality control of iron and steel products, the secretariat of which is held by ibn. The standard governing surface defects and permissible ground areas of hot rolled plates is en 10163. Hot rolled round steel bars for general purposes dimensions.
En 10051, continuously hotrolled uncoated plate, sheet and strip of nonalloy and alloy steels tolerances on dimensions and shape. Tolerances on the flatness, class n nominal thickness steel type l steel type h measuring length 2000 2000 93 10051. For the time being please refer to the stainless steel advisory service. Tolerances to en 10051 for continuously rolled hot rolled. This european standard does not apply to stainless steels and not to hotrolled strip rolled. Delivery requirements for surface condition of hotrolled. The four dimensional tolerance categories are a, b, c and d. Actual dimension of the bar shall be measured at least 150 mm from the end of the bar, in accordance to en 10278. It is intended to publish an article on this standard. View on information provider website linktext for assistance with locating previous versions, please contact the information provider. Ta evropski standard doloca tolerance mer in oblik za kontinuirno vroce valjane plocevine in trakove z najvecjo debelino 2200 mm iz nelegiranih in legiranih jekel brez prevleke v skladu s preglednico 1 glej tudi dodatek a. Din en 10051 continuously hotrolled strip and platesheet cut from wide strip of nonalloy and alloy steels tolerances on dimensions and shape.
Continuously hotrolled strip and platesheet cut from wide strip of nonalloy and alloy steels tolerances on dimensions and shape ssen 10051. Continuously hotrolled uncoated plate, sheet andstrip of nonalloy and alloy steels tolerances on dimensions and shape. Tolerances for sheet and plate thickness the tolerances on thickness for continuously hotrolled low carbon steel steelplate for cold forming according to en 10111 are given in table 1. Amendments din en 10147, july 2000 edition, din en 10154, august 2002 edition, and din en 10214 and din en 10215, april 1995 editions, have been superseded by the specifications of en 10326. En 10048, hot rolled narrow steel strip tolerances on dimensions and shape. Din v 17006100 is the standard corresponding to cen report cr 10260 referred to in clause 2 of the en. This european standard specifies tolerances on dimensions and shape for continuously hotrolled uncoated platesheet and strip with a maximum width of 2 200 mm of nonalloy and alloy steels in accordance with table 1 see also annex a.
12 686 25 3 106 55 1210 77 126 747 1199 339 871 1400 1013 44 1268 273 261 496 1470 695 1288 489 1117 1343 1383 1170 770 822 1114 919 1372 282